作者: HIGHWAY
来源:
pppppppppppppppppppppppppppppppppppppppppp
P级
AU OPTRONICS CORPORATION
Specification for Approval
INCOMING INSPECTION STANDARD FOR
19" TFT-LCD MODULES(200 Series)
Model Name: M190EN03
Approved By Prepared By
MP Huang Belinda Chen
Quality Management Division/AU Optronics Corporation
Customer Checked and Approved by
1. Scope:
1.1 The incoming inspection standards shall be applied to TFT-LCD Modules (hereinafter called "Modules") that supplied by AU Optronics Corporation (hereinafter called "seller").
1.2 Specifications contains
l Electrical inspection specification
l Appearance specification
l Outside dimension specification
2. Incoming inspection:
The buyer (customer) shall inspect the modules within twenty calendar days of the delevery date (the "inspection period" ) at its own cost. The results of the inspection (acceptance or rejection) shall be recorded in writing, and a copy of this writing will be promptly sent to the seller.
The buyer may, under commercially reasonable reject procedures, reject an entire lot in the delivery involved if, within the inspection period ,such samples of modules within such lot show an unacceptable number of defects in accordance with this incoming inspection standards, provided however that the buyer must notify the seller in writing of any such rejection promptly, and not later than within three business days of the end of the inspection period.
Should the buyer fail to notify the seller within the inspection period, the buyer's right to reject the modules shall be lapsed and the modules shall be deemed to have been accepted by the buyer.
3. Inspection sampling method:
Unless otherwise agree in writing, the method of incoming inspection shall be based on MIL-STD-105E.
3.1 Lot size: Quantity per shipment lot per model.
3.2 Sampling type: Normal inspection, single sampling.
3.3 Sampling level: Level II.
3.4 Acceptable quality level (AQL):
Major defect: AQL=1.0%.
Minor defect: AQL=2.5%.
4. Inspection instruments:
4.1 Pattern generator: LD-2000 or equivalent model.
4.2 Video board: AU video board or equivalent. The output of the signal should comply with the specification provided by AU.
4.3 Luminance colorimeter: Topcon BM-7 or equivalent model
5. Inspection environment conditions:
5.1 Room temperature : 20 ~ 25 C
5.2 Humidity: 65± 5% RH.
5.3 Illumination: Fluorescent light (Day-Light Type) display surface illumination to be 300 ~ 700 Lux. (standard 500Lux.)
5.4 To be a distance about 35±5 cm in front of LCD unit, viewing line should be perpendicular to the surface of the module judge the visual appearance with human’s eyes.
5.5 Take off the protection film of polarizer while judging the display area.
5.6 If there is any question while judging, check the panel again in operating mode.
6. Classification of defects:
Defects are classified as major defects and minor defects according to the degree of defectiveness defined herein.
Major defects: A major defect is a defect that is likely to result in failure, or to reduce materially the usability of the product for its intended purpose.
Minor defects: A minor defect either is a defect that is not likely to reduce materially the usability of the product for its intended purpose, or is a departure from an established having little bearing on the effective use or operation of the product.
6.1 Electrical inspection specification
Inspection Item Specification
1 Line defect Can’t be seen.
2 Bright dots ≤ 2 dots (note1,2,3)
3 Dark dots ≤ 5 dots (note1,2,3)
4 Total dots defect ≤ 5 dots (note1,2,3)
5 Adjacent dot defect(note 3) Two continuous bright dots (vertical, horizontal, oblique): ≤ 1 pair
Three or more continuous bright dots (vertical, horizontal, oblique): Not allowed
Two continuous dark dots (vertical, horizontal, oblique): ≤ 2 pair
Two continuous dots – one dark dot adjacent to one bright dot (vertical, horizontal, oblique): ≤ 2 pair
Three or more continuous dots – to be of any combination of dark dot and bright dot (vertical, horizontal, oblique): Not allowed
Distance between 2 Bright dots: ≥ 15 mmDistance between 2 Dark dots: ≥ 15 mmDistance between Bright and Dark dots: ≥ 10 mm
6 Display scratch Refer to 6.2 Appearance specifications
7 Dust, stain, bubble Refer to 6.2 Appearance specifications
8 Polarizer scratch Refer to 6.2 Appearance specifications
9 Display Non - uniformity Not noticeable. (Note 4 & 5)
10 Newton ring Not noticeable. (Note 4 & 5)
11 Rubbing mark Not noticeable. (Note 4 & 5)
12 Dim line Not noticeable. (Note 4 & 5)
Note 1) For dot defect, one sub pixel is defined as one dot.
Note 2) Defect area (of dot defect) should be larger than 1/2 area of a subpixel to be count as 1 dot defect.
Note 3) Adjacent-dot defect should be observed under any one of white/Black/Green/Blue/Red pattern.
Note 4) The general mura symptoms will use 8 % ND Filter on gray pattern judged no noticeable.
Note 5) The inspection method of ND Filter - holding ND filter in front of the panel around 1 cm and examine the panel from 30±5 cm in the front view for 3 seconds.
Inspection patterns: Standard inspection patterns of dot defect are listed below. AU uses these patterns as standard criteria for judging dot defect. Please inform AU if any other pattern is to be used to examine dot defect.
Test Pattern Defect
Black For bright dot(s)
White For dark dot(s)
Red For bright and dark dot(s)
Green. . For bright and dark dot(s)
Blue For bright and dark dot(s)
Monotone Gray (128 Gray) For bright and dark dot(s)
6.2 Appearance inspection specification
Judge area Judge item Inspection specification Judge criterion
Critical Major Minor
Active Area Particles, scratch and bubbles in display area(note 1) Round Average diameter (D) :(mm) Numbers (N) m
D < 0.15 Disregarded
0.15 ≤ D ≤ 0.5 N ≤ 5
0.5 < D N = 0
Linear Width: W (mm) Length: L (mm) Numbers O
W< 0.05 and L < 2 Disregarded
0.05≤ W≤0.07 or 2 ≤ L ≤ 5 N ≤ 3
W> 0.1 or L >5 N = 0
Defect Eyes should not find it. O
Dirt O
Grains O
Bubble in cell (Active area) Eyes should not find it. O
From active area outside 1.7mm The end of polarizer The edge of polarizer can’t be seen. O
Bezel Scratch No harm O
Dirt O
Wrap No dangerous O
Sunken No harm O
Label(S/N, B/L, Week code) No label No O
Invert label O
Broken O
Dirt Word can be read. O
Not clear O
Word out of shape O
Mistake No O
Position Be attached on right position O
Solder Appearance Can’t see the abnormal color, shape, hurt, dirt (fused goods, etc.). If it is necessary, please prepare sample. O
Screw Not enough No O
Limp No O
White sheet Shell, rub No O
Connector Connection status Need correct connection. O
FPC/FFC Broken No O
BM area Around Red Line No concern O
Note 1: When L >=2W, defect count as liner defect.
6.3 Outside dimension specification:
Testing order Testing Item Specification Note
Name Unit Min Typ Max
1 Outside dimension (vertical) mm 323 324 325
2 Outside dimension (horizontal) mm 395 396 397
3 Outside dimension (thickness) mm 16.5 17.5 18.5 Note 1
4 Weight g -100 2400 +100
5 Display tolerance ABS (a-b) mm 1.2 Note 2
6 Display tolerance ABS (c-d) mm 1.2 Note 2
7 Panel gap (Y) mm 0.8 Note 3
Note 1: Thickness doesn’t include bending reason.
Note 2: Display tolerance definition
Note 3: Panel gap (Y) definition
7. Inspection judgement:
7-1 The judgement of the shipped lot (acceptance or rejection) should follow the sampling plan of MIL-STD-105E, single sampling, normal inspection, level II.
7-2 If the number of defects is equal to or less than the applicable acceptance level, the lot shall be accepted.
7-3 If the number of defects is more than the applicable acceptance level, the lot shall be rejected and the buyer should inform the seller of the result of incoming inspection in writing
8. Precaution:
Please pay attention to the following items when you use the LCD Module with back-light unit.
1. Do not twist or bend the module and prevent the unsuitable external force for display module during assembly.
2. Adopt measures for good heat radiation. Be sure to use the module with in the specified temperature.
3. Avoid dust or oil mist during assembly.
4. Follow the correct power sequence while operating. Do not apply the invalid signal, otherwise, it will cause improper shut down and damage the module.
5. Less EMI: it will be more safety and less noise.
6. Please operate module in suitable temperature. The response time & brightness will drift by different temperature.
7. Avoid to display the fixed pattern (exclude the white pattern) in a long period, otherwise, it will cause image sticking.
8. Be sure to turn off the power when connecting or disconnecting the circuit.
9. Polarizer scratches easily, please handle it carefully.
10. Display surface never likes dirt or stains.
11. A dewdrop may lead to destruction. Please wipe off any moisture before using module.
12. Sudden temperature changes cause condensation, and it will cause polarizer damaged.
13. High temperature and humidity may degrade performance. Please do not expose the module to the direct sunlight and so on.
14. Acetic acid or chlorine compounds are not friends with TFT display module.
15. Static electricity will damage the modules; please do not touch the module without any grounded device.
16. Do not disassemble and reassemble the module by self.
17. Be careful do not touch the rear side directly because of the backlight high voltage.
18. No strong vibration or shock. It will cause module broken.
19. Storage the modules in suitable environment with regular packing.
20. Be careful of injury from a broken display module. Please avoid the pressure adding to the surface (front or rear side) of modules, because it will cause the display non-uniformity or other function issue.
AU Optronics Corp.
No. 1, Li-Hsin Rd. II,
Science-Based Industrial Park,
Hsin-Chu City, Taiwan, R.O.C.
Tel :886-3-5008800
nnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn
N级
AU OPTRONICS CORPORATION
Specification for Approval
INCOMING INSPECTION STANDARD FOR
19" TFT-LCD MODULES(300 Series)
Model Name: M190EN03
Approved By Prepared By
MP Huang Belinda Chen
Quality Management Division/AU Optronics Corporation
Customer Checked and Approved by
1. Scope:
1.1 The incoming inspection standards shall be applied to TFT-LCD Modules (hereinafter called "Modules") that supplied by AU Optronics Corporation (hereinafter called "seller").
1.2 Specifications contains
l Electrical inspection specification
l Appearance specification
l Outside dimension specification
2. Incoming inspection:
The buyer (customer) shall inspect the modules within twenty calendar days of the delevery date (the "inspection period" ) at its own cost. The results of the inspection (acceptance or rejection) shall be recorded in writing, and a copy of this writing will be promptly sent to the seller.
The buyer may, under commercially reasonable reject procedures, reject an entire lot in the delivery involved if, within the inspection period ,such samples of modules within such lot show an unacceptable number of defects in accordance with this incoming inspection standards, provided however that the buyer must notify the seller in writing of any such rejection promptly, and not later than within three business days of the end of the inspection period.
Should the buyer fail to notify the seller within the inspection period, the buyer's right to reject the modules shall be lapsed and the modules shall be deemed to have been accepted by the buyer.
3. Inspection sampling method:
Unless otherwise agree in writing, the method of incoming inspection shall be based on MIL-STD-105E.
3.1 Lot size: Quantity per shipment lot per model.
3.2 Sampling type: Normal inspection, single sampling.
3.3 Sampling level: Level II.
3.4 Acceptable quality level (AQL):
Major defect: AQL=1.0%.
Minor defect: AQL=2.5%.
4. Inspection instruments:
4.1 Pattern generator: LD-2000 or equivalent model.
4.2 Video board: AU video board or equivalent. The output of the signal should comply with the specification provided by AU.
4.3 Luminance colorimeter: Topcon BM-7 or equivalent model
5. Inspection environment conditions:
5.1 Room temperature : 20 ~ 25 C
5.2 Humidity: 65± 5% RH.
5.3 Illumination: Fluorescent light (Day-Light Type) display surface illumination to be 300 ~ 700 Lux. (standard 500Lux.)
5.4 To be a distance about 35±5 cm in front of LCD unit, viewing line should be perpendicular to the surface of the module judge the visual appearance with human’s eyes.
5.5 Take off the protection film of polarizer while judging the display area.
5.6 If there is any question while judging, check the panel again in operating mode.
6. Classification of defects:
Defects are classified as major defects and minor defects according to the degree of defectiveness defined herein.
Major defects: A major defect is a defect that is likely to result in failure, or to reduce materially the usability of the product for its intended purpose.
Minor defects: A minor defect either is a defect that is not likely to reduce materially the usability of the product for its intended purpose, or is a departure from an established having little bearing on the effective use or operation of the product.
6.1 Electrical inspection specification
Inspection Item Specification
1 Line defect Can’t be seen.
2 Bright dots ≤ 6 dots (note1,2,3)
3 Dark dots ≤ 6 dots (note1,2,3)
4 Total dots defect ≤ 8 dots (note1,2,3)
5 Adjacent dot defect(note 3) Two continuous bright dots (vertical, horizontal, oblique): ≤ 2 pair
Three or more continuous bright dots (vertical, horizontal, oblique): Not allowed
Two continuous dark dots (vertical, horizontal, oblique): ≤ 2 pair
Two continuous dots – one dark dot adjacent to one bright dot (vertical, horizontal, oblique): ≤ 2 pair
Three or more continuous dots – to be of any combination of dark dot and bright dot (vertical, horizontal, oblique): Not allowed
Distance between 2 Bright dots: ≥ 15 mmDistance between 2 Dark dots: ≥ 5 mmDistance between Bright and Dark dots: ≥ 5 mm
6 Display scratch Refer to 6.2 Appearance specifications
7 Dust, stain, bubble Refer to 6.2 Appearance specifications
8 Polarizer scratch Refer to 6.2 Appearance specifications
9 Display Non - uniformity Not noticeable. (Note 4 & 5)
10 Newton ring Not noticeable. (Note 4 & 5)
11 Rubbing mark Not noticeable. (Note 4 & 5)
12 Dim line Not noticeable. (Note 4 & 5)
Note 1) For dot defect, one sub pixel is defined as one dot.
Note 2) Defect area (of dot defect) should be larger than 1/2 area of a subpixel to be count as 1 dot defect.
Note 3) Adjacent-dot defect should be observed under any one of white/Black/Green/Blue/Red pattern.
Note 4) The general mura symptoms will use 5 % ND Filter on gray pattern judged no noticeable.
Note 5) The inspection method of ND Filter - holding ND filter in front of the panel around 1 cm and examine the panel from 30±5 cm in the front view for 3 seconds.
*Inspection patterns: Standard inspection patterns of dot defect are listed below. AU uses these patterns as standard criteria for judging dot defect. Please inform AU if any other pattern is to be used to examine dot defect.
Test Pattern Defect
Black For bright dot(s)
White For dark dot(s)
Red For bright and dark dot(s)
Green. . For bright and dark dot(s)
Blue For bright and dark dot(s)
Monotone Gray (128 Gray) For bright and dark dot(s)
6.2 Appearance inspection specification
Judge area Judge item Inspection specification Judge criterion
Critical Major Minor
Active Area Particles, scratch and bubbles in display area(note 1) Round Average diameter (D) :(mm) Numbers (N) m
D < 0.15 Disregarded
0.15 ≤ D ≤ 0.8 N ≤ 5
0.5 < D N = 0
Linear Width: W (mm) Length: L (mm) Numbers O
W< 0.05 and L < 5 Disregarded
0.05≤ W≤ 0.07 or 2 ≤ L ≤ 10 N ≤ 5
W> 0.07 or L >10 N = 0
Defect Eyes should not find it. O
Dirt O
Grains O
Bubble in cell (Active area) Eyes should not find it. O
From active area outside 1.7mm The end of polarizer The edge of polarizer can’t be seen. O
Bezel Scratch No harm O
Dirt O
Wrap No dangerous O
Sunken No harm O
Label(S/N, B/L, Week code) No label No O
Invert label O
Broken O
Dirt Word can be read. O
Not clear O
Word out of shape O
Mistake No O
Position Be attached on right position O
Solder Appearance Can’t see the abnormal color, shape, hurt, dirt (fused goods, etc.). If it is necessary, please prepare sample. O
Screw Not enough No O
Limp No O
White sheet Shell, rub No O
Connector Connection status Need correct connection. O
FPC/FFC Broken No O
BM area Around Red Line No concern O
Note 1: When L >=2W, defect count as liner defect.
6.3 Outside dimension specification:
Testing order Testing Item Specification Note
Name Unit Min Typ Max
1 Outside dimension (vertical) mm 323 324 325
2 Outside dimension (horizontal) mm 395 396 397
3 Outside dimension (thickness) mm 16.5 17.5 18.5 Note 1
4 Weight g -100 2400 +100
5 Display tolerance ABS (a-b) mm 1.2 Note 2
6 Display tolerance ABS (c-d) mm 1.2 Note 2
7 Panel gap (Y) mm 0.8 Note 3
Note 1: Thickness doesn’t include bending reason.
Note 2: Display tolerance definition
Note 3: Panel gap (Y) definition
7. Inspection judgement:
7-1 The judgement of the shipped lot (acceptance or rejection) should follow the sampling plan of MIL-STD-105E, single sampling, normal inspection, level II.
7-2 If the number of defects is equal to or less than the applicable acceptance level, the lot shall be accepted.
7-3 If the number of defects is more than the applicable acceptance level, the lot shall be rejected and the buyer should inform the seller of the result of incoming inspection in writing
8. Precaution:
Please pay attention to the following items when you use the LCD Module with back-light unit.
1. Do not twist or bend the module and prevent the unsuitable external force for display module during assembly.
2. Adopt measures for good heat radiation. Be sure to use the module with in the specified temperature.
3. Avoid dust or oil mist during assembly.
4. Follow the correct power sequence while operating. Do not apply the invalid signal, otherwise, it will cause improper shut down and damage the module.
5. Less EMI: it will be more safety and less noise.
6. Please operate module in suitable temperature. The response time & brightness will drift by different temperature.
7. Avoid to display the fixed pattern (exclude the white pattern) in a long period, otherwise, it will cause image sticking.
8. Be sure to turn off the power when connecting or disconnecting the circuit.
9. Polarizer scratches easily, please handle it carefully.
10. Display surface never likes dirt or stains.
11. A dewdrop may lead to destruction. Please wipe off any moisture before using module.
12. Sudden temperature changes cause condensation, and it will cause polarizer damaged.
13. High temperature and humidity may degrade performance. Please do not expose the module to the direct sunlight and so on.
14. Acetic acid or chlorine compounds are not friends with TFT display module.
15. Static electricity will damage the modules; please do not touch the module without any grounded device.
16. Do not disassemble and reassemble the module by self.
17. Be careful do not touch the rear side directly because of the backlight high voltage.
18. No strong vibration or shock. It will cause module broken.
19. Storage the modules in suitable environment with regular packing.
20. Be careful of injury from a broken display module. Please avoid the pressure adding to the surface (front or rear side) of modules, because it will cause the display non-uniformity or other function issue.
AU Optronics Corp.
No. 1, Li-Hsin Rd. II,
Science-Based Industrial Park,
Hsin-Chu City, Taiwan, R.O.C.
Tel :886-3-5008800
vvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv
V级
AU OPTRONICS CORPORATION
Specification for Approval
INCOMING INSPECTION STANDARD FOR
19" TFT-LCD MODULES(400 Series)
Model Name: M190EN03
Approved By Prepared By
MP Huang Belinda Chen
Quality Management Division/AU Optronics Corporation
Customer Checked and Approved by
1. Scope:
1.1 The incoming inspection standards shall be applied to TFT-LCD Modules (hereinafter called "Modules") that supplied by AU Optronics Corporation (hereinafter called "seller").
1.2 Specifications contains
l Electrical inspection specification
l Appearance specification
l Outside dimension specification
2. Incoming inspection:
The buyer (customer) shall inspect the modules within twenty calendar days of the delevery date (the "inspection period" ) at its own cost. The results of the inspection (acceptance or rejection) shall be recorded in writing, and a copy of this writing will be promptly sent to the seller.
The buyer may, under commercially reasonable reject procedures, reject an entire lot in the delivery involved if, within the inspection period ,such samples of modules within such lot show an unacceptable number of defects in accordance with this incoming inspection standards, provided however that the buyer must notify the seller in writing of any such rejection promptly, and not later than within three business days of the end of the inspection period.
Should the buyer fail to notify the seller within the inspection period, the buyer's right to reject the modules shall be lapsed and the modules shall be deemed to have been accepted by the buyer.
3. Inspection sampling method:
Unless otherwise agree in writing, the method of incoming inspection shall be based on MIL-STD-105E.
3.1 Lot size: Quantity per shipment lot per model.
3.2 Sampling type: Normal inspection, single sampling.
3.3 Sampling level: Level II.
3.4 Acceptable quality level (AQL):
N/A
4. Inspection instruments:
4.1 Pattern generator: LD-2000 or equivalent model.
4.2 Video board: AU video board or equivalent. The output of the signal should comply with the specification provided by AU.
4.3 Luminance colorimeter: Topcon BM-7 or equivalent model
5. Inspection environment conditions:
5.1 Room temperature : 20 ~ 25 C
5.2 Humidity: 65± 5% RH.
5.3 Illumination: Fluorescent light (Day-Light Type) display surface illumination to be 300 ~ 700 Lux. (standard 500Lux.)
5.4 To be a distance about 35±5 cm in front of LCD unit, viewing line should be perpendicular to the surface of the module judge the visual appearance with human’s eyes.
5.5 Take off the protection film of polarizer while judging the display area.
5.6 If there is any question while judging, check the panel again in operating mode.
6. Classification of defects:
Defects are classified as major defects and minor defects according to the degree of defectiveness defined herein.
Major defects: A major defect is a defect that is likely to result in failure, or to reduce materially the usability of the product for its intended purpose.
Minor defects: A minor defect either is a defect that is not likely to reduce materially the usability of the product for its intended purpose, or is a departure from an established having little bearing on the effective use or operation of the product.
6.1 Electrical inspection specification
Inspection Item Specification
1 Line defect Can’t be seen.
2 Bright dots ≤ total dots defect. (note1,2,3)
3 Green bright dots ≤ total dots defect.
4 Dark dots ≤ total dots defect. (note1,2,3)
5 Total dots defect ≤ 20 dots (note1,2,3)
6 Adjacent dot defect(note 3) Two continuous bright dots (vertical, horizontal, oblique): ≤ 3 pair
Three or more continuous bright dots (vertical, horizontal, oblique): ≤ 1 triple
Two continuous dark dots (vertical, horizontal, oblique): ≤ 3 pair
Two continuous dots – one dark dot adjacent to one bright dot (vertical, horizontal, oblique): ≤ 3 pair
Three or more continuous dots – to be of any combination of dark dot and bright dot (vertical, horizontal, oblique): ≤ 1 triple
Distance between 2 Bright dots: no countDistance between 2 Dark dots: no countDistance between Bright and Dark dots: no count
7 Display scratch Refer to 6.2 Appearance specifications
8 Dust, stain, bubble Refer to 6.2 Appearance specifications
9 Polarizer scratch Refer to 6.2 Appearance specifications
10 Display Non - uniformity Not noticeable or set up limit sample.
11 Newton ring Not noticeable or set up limit sample.
12 Rubbing mark Not noticeable or set up limit sample.
Note 1) For dot defect, one sub pixel is defined as one dot.
Note 2) Defect area (of dot defect) should be larger than 1/2 area of a subpixel to be count as 1 dot defect.
Note 3) Adjacent-dot defect should be observed under any one of white/Black/Green/Blue/Red pattern.
Note 4) The general mura symptoms will use 2 % ND Filter on gray pattern judged no noticeable.
Note 5) The inspection method of ND Filter - holding ND filter in front of the panel around 1 cm and examine the panel from 30±5 cm in the front view for 3 seconds.
*Inspection patterns: Standard inspection patterns of dot defect are listed below. AU uses these patterns as standard criteria for judging dot defect. Please inform AU if any other pattern is to be used to examine dot defect.
Test Pattern Defect
Black For bright dot(s)
White For dark dot(s)
Red For bright and dark dot(s)
Green. . For bright and dark dot(s)
Blue For bright and dark dot(s)
Monotone Gray (128 Gray) For bright and dark dot(s)
6.2 Appearance inspection specification
Judge area Judge item Inspection specification Judge criterion
Critical Major Minor
Active Area Particles, scratch and bubbles in display area(note 1) Round Average diameter (D) :(mm) Numbers (N) m
D < 0.15 Disregarded
0.15 ≤ D ≤ 1.0 N ≤ 5
1.0 < D N = 0
Linear Width: W (mm) Length: L (mm) Numbers O
W< 0.05 and L < 2 Disregarded
0.05≤ W≤ 0.1 or 2 ≤ L ≤ 15 N ≤ 5
W> 0.1 or L >15 N = 0
Defect Eyes should not find it. O
Dirt O
Grains O
Bubble in cell (Active area) Eyes should not find it. O
From active area outside 1.7mm The end of polarizer The edge of polarizer can’t be seen. O
Bezel Scratch No harm O
Dirt O
Wrap No dangerous O
Sunken No harm O
Label(S/N, B/L, Week code) No label No O
